Victron Lynx Smart BMS 1000 NG (M10) – intelligent lithium battery management system

Victron Energy Lynx Smart BMS 1000 NG (M10) is an advanced battery management and protection system designed specifically for Victron Energy Lithium NG batteries. It monitors the battery bank, controls chargers and loads, and protects the system against unsafe conditions such as low cell voltage and excessive discharge.

The unit features a built-in main safety contactor rated for 1000 A continuous current and up to 1200 A for 5 minutes. Bluetooth, VictronConnect, VE.Can, Victron GX compatibility and VRM integration provide convenient local and remote configuration, monitoring and diagnostics. M10 busbar connections allow seamless integration with other products in the modular Lynx Distribution system.

Key benefits

• Designed specifically for Victron Energy Lithium NG batteries.
• Supports 12 V, 24 V and 48 V systems.
• Built-in main safety contactor rated at 1000 A continuous and 1200 A for 5 minutes.
• Monitors state of charge and key battery-bank data.
• Pre-alarm signal warns before shutdown caused by low cell voltage.
• Controls chargers and loads through Allow-to-Charge and Allow-to-Discharge outputs.
• Supports remote On, Off and Standby control.
• Bluetooth connectivity for setup, monitoring and diagnostics through VictronConnect.
• VE.Can interface for connection to Victron GX devices.
• Compatible with all Lynx products using M10 busbar connections.
• Up to 50 Lithium NG batteries can be connected to one BMS system.

Applications

Victron Energy Lynx Smart BMS 1000 NG (M10) is suitable for medium and large energy systems using Victron Lithium NG batteries. Typical applications include campervans and caravans, yachts and marine systems, professional vehicles, off-grid installations and stationary energy-storage systems requiring high current handling, detailed monitoring and integration with Victron GX equipment.

Technical specifications

• Product: Lynx Smart BMS 1000 NG (M10)
• SKU: LYN034170310
• Designed for: Victron Energy Lithium NG batteries
• Supported system voltages: 12 V, 24 V and 48 V
• Supply voltage range: 9–60 VDC
• Maximum input voltage: 75 VDC
• Main safety contactor: 1000 A continuous
• Contactor peak current: 1200 A for 5 minutes
• Power consumption in OFF mode: 0.3 mA
• Power consumption in Standby mode: approximately 0.6 W; 50 mA at 12 V
• Power consumption in ON mode: approximately 4.2 W; 350 mA at 12 V, depending on relay state
• Minimum pre-charge load resistance: 10 Ω or higher for 12 V systems; 20 Ω or higher for 24 V and 48 V systems
• AUX output maximum current: 1.1 A continuous; protected by a resettable fuse
• Allow-to-Charge port: maximum 0.5 A at 60 VDC
• Allow-to-Discharge port: maximum 0.5 A at 60 VDC
• Programmable alarm relay: SPDT, maximum 2 A at 60 VDC
• Busbar connections: M10; recommended torque 33 Nm
• Communication: VE.Can via RJ45
• Inputs and outputs: removable 13-pin connector with screw terminals
• Battery connection: circular 3-pole connectors with M8 screw ring
• Enclosure: ABS
• Dimensions: 230 × 180 × 100 mm
• Weight: 2.7 kg
• Busbar material: tinned copper
• Busbar dimensions: 8 × 30 mm
• Operating temperature: −40°C to +60°C
• Storage temperature: −40°C to +60°C
• Humidity: maximum 95%, non-condensing
• Protection rating: IP22
• Reverse polarity protection: no
• Standards: EN-IEC 63000:2018; EN-IEC 61000-6-3:2007/A1:2011/AC:2012; NEN-EN-ISO 9001:2015

Connectivity and control

The built-in Bluetooth interface enables configuration, monitoring and diagnostics through the VictronConnect app. Via VE.Can, the Lynx Smart BMS 1000 NG can connect to Victron GX devices such as the Cerbo GX and Ekrano GX for local monitoring and integration into a larger energy system. When a GX device is used, remote monitoring and control through the VRM Portal are also available.

The BMS can control chargers and loads through the Allow-to-Charge and Allow-to-Discharge signals. A programmable alarm relay, AUX output and remote On, Off and Standby modes are also provided.